Dollhouse Miniature Wire Bird Cage No Soldering Tutorial · Uncategorized

Miniature Bird Cage Tutorial No soldering!

I just love little bird cages and for the longest time have had a desire to make one.  I just hate soldering.  Soldering is not my friend.  I have made progress on getting some things to solder some of the times.   But I am not consistent every time.  So….I had to think of a different way to get my little cage done.   Paper, wire and glue are the main components.

BIRD CAGE finished close up.jpg

Let’s have some fun.


BIRD CAGE_ supplies.jpg


  1. wire 30 gauge
  2. card stock
  3. form  ( I used the glass from the bead landing cloches)
  4. Bottom portion from a small gumball machine container.   This will be the bottom of the cage.
  5. earring backs for pierced ears.   The bell shaped ones.
  6. some small filigree bead spacers
  7. paint
  8. glue white
  9. super glue
  10. tooth pick
  11. sand paper
  12. 3mm wide wood strip for spacing.

Cut a strip of the white card stock approximately 1/8 ” wide and one strip 1/4 ” wide.  Use the 1/4″ strip to form a band along the bottom of the glass.  Form two 1/8″ bands /rings.   Placing one approximately 1/16″ above the bottom band and the other approximately 3/4″ above.  Right before the glass starts to curve.  Please note…do not glue the bands to the glass.  Over lap the strips ends and only glue the paper to paper.  BIRD CAGE with paper bands.JPG

Cut a 1/2 circle of card stock and use a ball stylus to round out.  Use one very small dot of glue to hold to the top of the glass.

BIRD CAGE with top circle top view.jpg

Cut 34 lengths of the 30 gauge wire approximately 2.5″ long.   You may need more or less depending on your spacing.  Apply glue only  to the paper and align a wire running from top to the bottom.

BIRD CAGE first wire.jpgBIRD CAGE first wire close.jpg

Try and have the wire run straight as possible from the top to the bottom.  Cut off  any excess wire you have hanging over the edge.   Mine is definitely crooked.

I used a piece of wood that is 3 mm in width to make a light mark for the next wire.

BIRD CAGE with wood spacer.jpg

Glue your next piece of wire on the mark.

BIRD CAGE three wires on.jpg

Keep the wires on the marks as close as possible.  The spacing at the top the wires will be closer together.   Continue on until you fill to the end.


Cut a 2 strips 1/8″, one 1/4″ and another 1/2″ circle.  Glue over the first strips.  Making a sandwich of the wires.

BIRD CAGE fini second paper layer.jpg


Let dry thoroughly. Gently work the rough cage off of the glass dome.  BIRD CAGE removing from form.jpg

BIRD CAGE removed.jpg

Test fit the bottom of the bubble gum machine container.

BIRD CAGE test fit bottom.jpg

Cut a 2.5″ piece of the 30 gauge wire and form a loop at one end.

BIRD CAGE wire eye.jpg

Thread on an earring backing, small circle bead spacer and then pierce through the bottom of the circle through to the top circle.

BIRD CAGE threaded first finial.jpg


BIRD CAGE top finial test assemble.jpg

This picture shows a test fit of the top filigree circles finished off with the earring back.  I changed to a flat filigree vs the dome in my finished project as below.

BIRD CAGE swing made.jpg

Once you have your choice of top filigree spacers, make a round loop for the top.

Next we will work on the door for the cage.  It will be a sliding door that slides up.   Cut four  wires right above the second band from the bottom and then cut again the same three wires about 1/3″ above.  You will have a small rectangle opening.

BIRD CAGE cage door frame.jpg

Cut a piece of the 30 gauge wire to frame the opening and  super glue (I use gorilla gel super glue) glue across the cut wires at the top. The picture above shows the wire in place painted white to see.

Cut four pieces of the 30 gauge wire approximately 1/2″ and two pieces 3/4″ long.

BIRD CAGE door on tap.jpg

I used the back side of a piece of masking tape to hold the wires in place.  Four across vertical and then two across horizontal.   Be sure to use your spacing wood to space the bars for the gate so that they will match the cage.  The door will need to be just a tad bit taller then the opening.    Glue with the super glue.

I happened to find an interesting glue “helper” in the hobby store.  The sales team member said it would work with the liquid super glue, however, I found that it works with the gel super glue just fine.  It’s called Johnny weld.  You are supposed to pour a little bit of the johnny weld sand on the connection and then add a drop of the liquid super glue.  I , however,  did it the opposite way on my cage door.  I placed the gel super glue on the joins  ( very sparingly) and then with a paper towel under to catch the extra johnny weld, I poured on top of the joins.  The Johnny weld helps make a stronger bond.

BIRD CAGE_johnny weld.jpg

BIRD CAGE door.jpg

Trim off the extra wire at the top and bottom.  The above picture shows the johnny weld on the back of the cage door.

Trim off the side wire to extend 1/8″ over the last wire. Bend you door around the glass shape so that it will be rounded slightly.

Place the door over the opening.  Making sure that the top wire of the cage door is above the door frame top wire.  Bend over the wires at the sides in a “u” shape around the vertical wires.  Not too tightly.  The door will need to be able to slide up and down.

BIRD CAGE finished door open.jpg

Sand down a tooth pick to about half the width.

BIRD CAGE tooth pick sanded.jpg

Measure a width across the cage for the bird perch.  Cut  and notch the ends to fit between the wires.

Cut another piece of the toothpick about a 1/4″ wide.   Use a t-pin to make holes in each end.

BIRD CAGE tooth pick swing.jpgBIRD CAGE wire for swing.jpg

Cut a small piece of the 30 gauge wire and shape as above.   I missed a picture.  Trim the length to a little over 1/4″  bend the ends of the wire in toward the middle and trim off. Insert the legs into the ends of the wood.  This is the swing that hangs from the loop on the inside of the cage.  BIRD CAGE swing made.jpg


All done with the hard part.  Now you can paint and decorate as you wish to finish up your bird cage.  I recommend sealing the paper with a sealer before painting  with acrylics to prevent warping.   I spray painted flat white primer on my cage for my sealer.

You can make a simple stand by bending wire to form a hook.

BIRD CAGE finished close up.jpg

BIRD CAGE painted on stand.jpg


I hope everyone had a lovely Easter holiday!






22 thoughts on “Miniature Bird Cage Tutorial No soldering!

  1. I knew I could count on you. You never disappoint. So pretty with the morning glories. Thank you and hope you had a peaceful Easter.


  2. Just signed up and saw the tutorial on the bird cage, what a cleaver girl you are👍Thanks for sharing.
    I am 74 and making two doll houses for my great grand children. Furniture is so expensive so this is doable sooo
    Grateful for your generosity of sharing😇


  3. I just found your site from Kris Compas’s. First thing tomorrow, I’m making the little bird cage and the lawn chairs. They are adorable! Thank you so much for doing these easy-to-understand tutorials – it brings me and my granddaughters so much pleasure to be able to make lovely little things for our dollhouse.


  4. Hi Tina! It appears that Great Minds think alike 😀
    I posted a Very Similar tutorial to yours early last year which you might wish to see. It’s entitled “La Cage… Oh, Faux!” Mine cages are more Shabby and yours is much more Chic but the techniques are quite close.
    Even so, I LOVE the look of your dainty bird cage and I may give the fine wire a try since the results look Very Pretty! ♡
    But before I forget…. I learned a neat trick from another blogger which you might enjoy as well, that applying Super Glue and then a sprinkling of baking soda over top will make a really solid bond just as the Johnny Weld does. I been using this method for a while and it really works! 😀



    1. Hi Elizabeth! Oh my goodness, so close and yet different. 🙂 Thanks for the baking soda/ glue tip. I have tried it in flower making but not on wire to wire. It will be much more economical than the Johnny weld. Best Tina


  5. Your tutorials look great. I have been wanting to make a birdcage but was not sure how to begin; now you have provided great directions along with clear pictures. Thanks!


Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s